DP Communication Controller APC3
- Microcyber
- China
- In Stock
- 500 Sets/Month
DP Communication Controller APC3 is an ASICs chip for PROFIBUS DP intelligent slave station development. APC3 supports the DPV0 part of the PROFIBUS DP standard.
1. Pin definition is compatible with VPC3 in 2K mode
2. Automatic identification of 9.6Kbps~12Mbps baud rate
3. Support Intel and Motorola processor interface modes
4. Integrated 1.5KByte dual-port RAM
5. Working temperature: -40℃~85℃
6. Power supply voltage: 3.3V
7. Compatible with SPC3LV
DP Communication Controller APC3 Compatibility:
Under the condition of 3.3v working voltage, it is fully compatible with the VPC3 operating in DPV0 mode.
It is fully compatible with SPC3 operating in DPV0 mode except for the operating voltage
Processor Interface:
Support Intel and Motorola two processor interface mode; The interface MODE can be configured through XINT/MOT and MODE pins.
With a synchronous/asynchronous 8-bit data interface and an 11-bit address bus, users can directly manipulate internal dual-port RAM
DP Communication Controller The clock:
APC3 needs to provide a 48MHZ external clock;
APC3 can output 24M/12M clocks to external processors
Software interface:
APC3 integrates 1.5k dual-port RAM, which is mainly used for the interface between APC3 and software;
Dual-port RAM is divided into 192 segments, each containing 8 bytes.Software operates on two-port RAM in segments
Status indication:
The MAC State in APC3 can be queried at any time through the State register, such as Offline/ passive-idle, dp-state, wd-state, Baud rate State, etc.
Various external events can be obtained through the interrupt request register to obtain relevant data, such as user extension parameter data
Baud Rate Identification:
APC3 can automatically recognize baud rates in the range of 9.6Kbps~12Mbps.
The baud rates were 12M, 6M, 3M, 1.5m, 500k, 187.5k, 93.75k, 45.45k, 19.2k, 9.6k, BPS
Temperature Characteristics:
Storage temperature: -65~150℃
Operating temperature: -40~85℃
Junction temperature: - 40 ~ 85 ℃
Features
Compatible with VPC3 in mode DPVO, at the working voltage 3.3V
compatible with SPC3LV, at the working voltage 3.3V
Automatic indentifcation of 9.6Kpbs~12Mbps baud rate
Support Intel and Motorola processing interface modes
Pin Function Definition
APC3 is packaged with PQFP with 44 pins. Pin definitions are shown in table below.
Pin Outgoing Definition
APC3 is packaged with 44-pin PQFP, as follows.
APC3 Pin outgoing definition
Interface Configuration
APC3 USES two pins (XINT/MOT,MODE or to configure the processor interface.
Processor interface
Application Examples (Principles)
Low Cost System with 80C32
80C32 System with External Memory
80286 System (X86 Mode)
Application with the 80C165
The pull-up/pull-down resistance in the figure above exists only on the circuit tester.
Application with the 80C32
The pull-up/pull-down resistance in the figure above exists only on the circuit tester.When the address line A11...The internal slice selection logic unit is available when A15 is set to 0.In the example above, the starting address of APC3 is set to 0X1000.
Package Information
APC3 is packaged in pqfp-44.
Typical Application:
DP Communication Controller FAQ
Q: Can I get a free electronic manual?
A: Yes, if you want it, please contact us.
Q: Can APC3 DP Communication Controller perform automatic baud rate recognition?
A: APC3 automatically recognizes baud rates.After each reset, or after the watchdog timer timeout, APC3 goes into "baud rate search" mode.
Q: Can you provided OEM service?
A: Yes, we can, such as communication board, we can also provided fieldbus development toolkit.
Hot Products--DP Communication Controller
